ISO 9001 Certified | ~40 Years Experience

Fine Blanking Machines Built Around Your Part, Die and Production Line

Send us a part drawing. We reverse-engineer the die envelope, material grade and production volume into a complete fine blanking line — press, coil feed, tooling interface and deburring cell — calibrated to deliver 100% shear-edge quality at the SPM your line requires. No catalog presses. No generic configurations.

Browse HF-Series Machines Request a Quote

Years Experience

30000

m² Facility

126

Employees

Press Models

200

-1200T Range

HF-Series Platform

Choose Your Fine Blanking Press

The nine HF-series platforms span 200T to 1200T, but tonnage alone never determines the configuration. Our engineers start from your part drawing: material thickness, shear perimeter, die-roll allowance and target SPM dictate the V-ring force, counter-pressure and die envelope — then we match the platform to those requirements.

HF-200

HF-200 Fine Blanking Press

When your part demands 100% shear-edge quality on brass connectors or low-carbon steel lock cylinders up to 8mm thick, but annual volume doesn't justify a 400T platform, the HF-200 delivers fine-blanked precision at conventional-stamping throughput rates — up to 80 SPM with independently programmable V-ring and counter-pressure.

200TView Details →

HF-320

HF-320 Fine Blanking Press

The sweet spot for automotive seat-recliner gears and clutch plates in 16MnCr5 or C45 up to 12mm. When a Tier-1 supplier needs 70 SPM with die-roll under 10% of material thickness and IT7-8 hole-to-profile positioning, the HF-320's triple-action hydraulic system — 1600 kN V-ring, 800 kN counter-pressure — holds flatness within 0.05mm across the full stroke.

320TView Details →

HF-400

HF-400 Fine Blanking Press

When brake backing plates in HSLA S500MC or door-latch components in C45 require burr-free shear edges at 14mm thickness, the HF-400 provides the 2000 kN V-ring impingement force needed to prevent fracture-zone tearing. The 650x650mm working table accommodates larger die sets for multi-station progressive layouts.

400TView Details →

HF-500

HF-500 Fine Blanking Press

Engineered for powertrain brackets and brake-caliper mountings in S500MC or 16MnCr5 up to 15mm. When a buyer is migrating from machined-finish parts to fine blanking, the HF-500's 2500 kN ring-gear force and 1250 kN counter-pressure produce shear edges that replace milling and grinding — cutting per-part cost by 40-60% on high-volume structural components.

500TView Details →

HF-650

HF-650 Fine Blanking Press

Selected when transmission ring gears exceed 200mm pitch diameter or thick-plate structural parts reach 16mm in 16MnCr5. The HF-650's 3250 kN V-ring force maintains full material impingement on high-carbon and alloy steels where die-roll must stay below 0.3mm — critical for gear teeth that mesh directly after blanking with no secondary machining.

650TView Details →

HF-700

HF-700 Fine Blanking Press

Built for multi-station progressive die applications where a single stroke produces a finished assembly-ready component — think seat-track locking plates or seatbelt retractor gears with formed features and pierced holes in one pass. The 900x900mm table and 3500 kN V-ring force support complex die stacks up to 18mm material thickness.

700TView Details →

HF-800

HF-800 Fine Blanking Press

When truck chassis brackets, agricultural machinery linkage plates or heavy-equipment sprockets demand 20mm-thick fine-blanked edges in S500MC or C60, the HF-800 delivers 4000 kN V-ring impingement with a 950x950mm die envelope. Buyers replacing flame-cut + machined parts see payback in 8-14 months at typical heavy-industry volumes.

800TView Details →

HF-1000

HF-1000 Fine Blanking Press

For oversized powertrain housings, crane sheave plates and rail-vehicle structural components up to 22mm thick. The HF-1000's 5000 kN ring-gear force and 2500 kN counter-pressure maintain fracture-free shear on high-strength alloy steels where conventional blanking would produce torn edges and require secondary machining across the entire part perimeter.

1000TView Details →

HF-1200

HF-1200 Fine Blanking Press

The flagship platform for the most demanding fine blanking applications — mining equipment wear plates, wind-turbine brake discs and heavy rail components up to 25mm in S700MC or equivalent. The HF-1200's 6000 kN V-ring force, 3000 kN counter-pressure and 1200x1200mm working table represent the ceiling of what triple-action hydraulic fine blanking can achieve in a single stroke.

1200TView Details →

View All Models & Specifications

Complete Production Line

Build a Complete Fine Blanking Line

A fine blanking press produces scrap without its peripheral ecosystem. Die envelope, strip width, material yield, deburring method and part-handling logic must be engineered as one cell — and that engineering starts before the press is selected, not after.

Press Platform

We calculate total blanking force from your part's shear perimeter, material thickness and shear strength — then add V-ring impingement and counter-pressure requirements. The result determines which HF platform and force configuration fits your die.

Material Feed

Strip width, coil weight and material grade dictate decoiler capacity, straightener roller count and feed pitch accuracy. We match the coil feeding system to your press cycle so strip advance stays synchronized at target SPM without misfeeds.

Die & Process

V-ring geometry, cutting clearance and ejector timing are co-engineered with the press force curves. Our tooling team reviews your die layout against the selected platform's die envelope, ram stroke and force availability before final specification.

Finishing

Burr removal, in-die sensing, part ejection and downstream inspection are integrated into the cell layout from day one. We specify deburring method — abrasive belt, vibratory or thermal — based on your part geometry and edge-quality acceptance criteria.

Configure Your Complete Line

Why Fine Blanking

One Press Stroke Can Replace Drilling, Milling, Grinding

⚙

Clean Edge Quality

A gear tooth blanked on an HF-series press emerges with a 100% smooth shear edge — no fracture zone, no secondary milling. On 16MnCr5 at 6mm, die-roll stays under 0.5mm and burr height below 0.1mm. One stroke replaces drilling, milling and grinding operations that would otherwise consume three machine setups and 40% more material.

⚡

Higher Efficiency

When a brake backing plate migrates from CNC machining to fine blanking, cycle time drops from 45 seconds to under 1 second at 60 SPM. Per-part cost falls 50-70% once volume exceeds 50,000 units annually, and dimensional repeatability improves from machining's natural variation to consistent IT7-8 across every part in the batch.

✓

Tight Tolerances

Fine blanking holds IT7-8 dimensional accuracy, flatness within 0.05mm and hole-to-profile positioning at ±0.02mm — in a single stroke, with no secondary sizing. On seat-recliner gears, this means teeth mesh at assembly without gauging or sorting. On connector terminals, it means pitch consistency that pick-and-place equipment can rely on at full line speed.

Applications

Fine Blanking Applications

Fine blanking is specified when a part requires a 100% shear edge, IT7-8 tolerance and controlled flatness — conditions that make conventional stamping insufficient and multi-axis machining uneconomical at volume.

Automotive

Seat-recliner gears in 16MnCr5 at 6mm requiring IT7-8 tooth positioning, brake-caliper brackets in S500MC at 12mm, transmission ring gears in C45 — all demanding 100% shear edges that eliminate secondary gear-tooth machining.

Gears & clutch plates
Seat recliner parts
Brake backing plates
Door lock components

Fine blanked lock cylinder and security hardware components

Locks & Hardware

Lock cylinders in brass or C45 requiring burr-free pin-tumbler bores at ±0.02mm, security-hardware deadbolts in case-hardened steel, and door-hinge brackets where shear-edge finish directly affects corrosion resistance and assembly fit.

Lock cylinders
Hinges & brackets
Security hardware

Fine blanked motor stator laminations and compressor valve plates on dark industrial background

Motors & Compressors

Rotor and stator laminations in electrical silicon steel at 0.5mm requiring burr control under 0.02mm for minimal interlaminar loss, and compressor valve plates in spring steel (50CrV4) at 2mm where flatness within 0.05mm determines valve-seat sealing performance.

Rotor & stator plates
Compressor valve plates
Motor laminations

Fine blanked electronic connector terminals and precision contacts on dark industrial background

Electronics

Connector terminals in phosphor bronze (C5191) at 0.3mm requiring pitch accuracy within ±0.01mm for high-density PCB insertion, and lead frames in copper alloy where burr-free edges prevent short-circuit paths in overmolded semiconductor packages.

Connector terminals
Lead frames
Precision contacts

Fine blanked surgical instrument components and medical device precision plates on dark background

Medical Devices

Surgical instrument components in 420 stainless steel at 3mm requiring burr-free edges for biocompatibility and autoclave readiness, and diagnostic-equipment precision plates where hole-to-hole positioning at ±0.02mm ensures sensor alignment in assembled instruments.

Surgical instruments
Implant components
Diagnostic parts

Industrial

Industrial clutch friction plates in C60 at 8mm, agricultural-equipment sprockets in 16MnCr5 at 12mm, and aerospace structural brackets in S500MC — components where replacing flame-cut-and-machined processes with fine blanking cuts lead time from weeks to days and per-part cost by up to 60%.

Industrial clutch plates
Agricultural parts
Aerospace components

Explore All Applications

Lifecycle Service

Restore a 15-Year-Old Feintool Press to 85% New Capability at 35% Replacement Cost

Multi-Brand Press Service

When a 15-year-old Feintool XTF or GKP press starts losing counter-pressure repeatability, plant managers face a choice: pay OEM service rates for a partial fix, replace the machine entirely, or call HS-FINEB. Our field service division restores Feintool, Mori, Schuler, Hydrel, Osterwalder, Asahi-Seiki and Nagano Seiko presses to 70-85% of original capability at 30-45% of replacement cost.

Every refurbishment begins with a documented condition report — hydraulic circuit pressure test, ram parallelism measurement, guide-column wear assessment and control-system diagnostic. We deliver a fixed-scope proposal with line-item costs before any work begins, so you can compare it directly against an OEM quote or a new-press capital request.

See Refurbishment Services

On-site fine blanking press refurbishment and cylinder rebuild service

On-site press refurbishment and retrofit service

Brands We Service

FEINTOOL MORI SCHULER HYDREL OSTERWALDER ASAHI-SEIKI NAGANO SEIKO

Brand names describe equipment platforms our engineers service. HS-FINEB is an independent service provider, not affiliated with these manufacturers.

Why HS-FINEB

Why Choose HS-FINEB

Four decades of fine blanking press engineering — not assembly, not trading. Every HF-series machine is configured around the buyer's part, die and production target, then manufactured in our own facility under ISO 9001:2015 process control.

Engineering-Driven Manufacturing

For nearly 40 years, HS-FINEB has designed and built fine blanking presses from 200T to 1200T. Our 30,000+ m² facility in Huangshi, Hubei houses the engineering team, CNC machining center, hydraulic test bench and assembly floor under one roof — meaning every ram, column and hydraulic manifold is manufactured, tested and integrated in-house, not sourced from third-party catalogs.

When you send a part drawing, our engineers calculate the exact blanking force, V-ring impingement requirement and counter-pressure ratio your material and geometry demand — then specify the platform, die envelope and feed system together. This is why buyers moving from conventional stamping or machining to fine blanking choose HS-FINEB: we engineer the process, not just ship a machine.

✓ ~40 years designing triple-action hydraulic fine blanking presses — not reselling or assembling catalog units
✓ ISO 9001:2015 and CE certified — every ram, column and hydraulic manifold manufactured under documented process control
✓ 30,000+ m² purpose-built facility — engineering, CNC machining, hydraulic testing and final assembly under one roof
✓ Part-drawing-driven engineering — force calculation, die-envelope matching and feed-line integration before the press is built

HS-FINEB fine blanking press manufacturing workshop in Huangshi, China

HS-FINEB ISO 9001 and CE quality management certifications

Send Your Part Drawing. Get a Line Configuration.

Send your drawing, material grade, thickness and annual volume. Within one business day, our engineers will return a platform recommendation, force calculation, die-envelope match and coil-feeding specification — or a refurbishment assessment if you're restoring an existing press.

Request a Quote Chat on WhatsApp

Technical Resources & Industry Insights

Deep-dive guides and engineering references for fine blanking professionals

⚙

💬

Fine Blanking Machines Built Around Your Part, Die and Production Line

Choose Your Fine Blanking Press

HF-200 Fine Blanking Press

HF-320 Fine Blanking Press

HF-400 Fine Blanking Press

HF-500 Fine Blanking Press

HF-650 Fine Blanking Press

HF-700 Fine Blanking Press

HF-800 Fine Blanking Press

HF-1000 Fine Blanking Press

HF-1200 Fine Blanking Press

Build a Complete Fine Blanking Line

Press Platform

Material Feed

Die & Process

Finishing

One Press Stroke Can Replace Drilling, Milling, Grinding

Clean Edge Quality

Higher Efficiency

Tight Tolerances

Fine Blanking Applications

Automotive

Locks & Hardware

Motors & Compressors

Electronics

Medical Devices

Industrial

Restore a 15-Year-Old Feintool Press to 85% New Capability at 35% Replacement Cost

Multi-Brand Press Service

Brands We Service

Why Choose HS-FINEB

Engineering-Driven Manufacturing

One Stroke Replaces Three Machining Operations

Send Your Part Drawing. Get a Line Configuration.

Technical Resources & Industry Insights

Fine Blanking Technology

Die Design & Tooling

Material Selection

Press Buying Guide

Complete Production Line

Deburring & Polishing

Case Studies

FAQ

Automotive Braking

Seat Mechanisms

Transmission Gears

Locks & Security

Electronics Connectors

Gear Solutions

Brake Caliper Solutions

Seat Recliner Solutions

Feintool Refurbishment

Mori Press Repair

Schuler Service

Progressive Die Design

Post-Processing Services

EV Lightweighting

Robot Components

Fuel Cell Plates

Motor Laminations

Troubleshooting Guide

Used Machines